Analysis of alum 1

A way to prevent this type of error is to ensure that all objects that come into contact with the alum have been thoroughly cleaned and dried first. Now if we measure the absorbance of a sample containing an unknown amount of analyte, it becomes a simple matter of substituting this value into the equation for our calibration curve and solving for the concentration.

Experimental Sources of Error: We figured out by calculation that there needs to be total of 42 mL of Ba NO3 2 to filter the precipitate completely. Unfortunately, this is neither a precise nor accurate way to make this determination. So, each week will have its own title, statement of purpose, etc.

A synthesis reaction is a reaction in which two or more chemicals are combined to create a new compound or compounds. Another error could have been made while massing out the crucible, the cover, or the anhydrous alum, which would throw off Analysis of alum 1 calculations when figuring out the mol to mol ratio of the given formulas.

When cooled, you can move the crucible to the bench top using the crucible tongs. Place the alum in the flame and heat it until the crystals begin to melt and the solid glows. I will heat and cool it over night. Because we know that the true ratio is 1: Use your glass stir rod to remove any crystals that adhere to the side of the beaker.

The most likely source of error was the obtainment of impurities. Potassium produces a distinctive lavender flame that we can use as a qualitative test for the presence of potassium.

The water can violently leave the alum at this point, if it is heated too strongly. When the aluminum has completely dissolved do not be concerned if the solution appears cloudy or contains black specksgravity filter the reaction mixture into a mL beaker through fluted filter paper the instructor will demonstrate.

Conclusions and Error Analysis Formula of a Hydrate: Some modifications that could be made to the procedure to help avoid this type of error are to make sure that the watch glass is securely on the evaporating dish, and to take extra precautions so as to avoid spillage. The different tests used to verify that the substance tested was alum was the melting point at which we knew that the crystal alum would melt at Rinse the crucible with distilled water and dry it before returning it to your drawer.

The isolation and purification of the products are based on physical properties such as the ability to form crystals, boiling point, melting point, solubility, etc.

Do not dip the pipet into the filtered solution! The balanced chemical reaction that occurs in this step is The overall balanced chemical reaction for the conversion of aluminum to alum, shown below, can be obtained by adding together the balanced chemical equation for each step Help Me.

Avoid inhaling the gas evolved during this reaction. If you collected a second crop of alum crystals, you should perform the sulfate and potassium qualitative tests on both the first and second crops are your two crops qualitatively the same? Once you have cleaned the crucible, it is important that you handle it only with the crucible tongs.Analysis of Alum AlK(SO4)2.

12H2O AP Chemistry Lab # 5 INTRODUCTION Every compound has a unique set of chemical and physical properties. To identify a compound with certainty, experiments have to be conducted in order to verify these properties. Preparation and Analysis of Alum 1. Authors: D.

L. McCurdy, V. M. Pultz and J. M. McCormick* Last Update: August 21, Introduction. One of chemistry’s goals is to be able to transform any set of substances (the reactants) to another set of substances (the products) through a chemical reaction. Lab report on synthesis of Alum using Aluminum.

1.

Preparation and Analysis of Alum

Purpose: In this experiment, you will be converting the aluminum metal from a beverage can into the chemical compound potassium aluminum sulfate, KAl(SO4)2•12 H2O, commonly referred to as alum. Data and Calculations: In this lab, a beverage can is used to get aluminum sheet and then.

Analysis of a Hydrate. Part 1: Approximately g of dry alum were pulverized with a mortar and pestle, and then packed into a capillary tube to a depth of about 1 cm. A rubber band was used to fasten the capillary tube to a thermometer with the alum level with the bulb of the thermometer.

The Formula, Synthesis, and Analysis of Alum

Mar 18,  · Analysis of Alum KAl (SO4)2. 12H2O Laayla Muhammad 10/31/06 /01/06 Purpose: To do several tests to determine if the resulting crystals are really alum, to use a Thiele melting point tube to determine the melting point of synthesized sample of alum and to determine the amount of water in a synthesized sample of alum and also the percent sulfate in a synthesized sample of alum.

Analysis of Alum, AlK(SO4)2•12H2O Post-Lab. David Danjul, Chem AP, PeriodMobley Procedure: Part I. Melting Point Determination of Alum5/5(1).

Download
Analysis of alum 1
Rated 4/5 based on 65 review